When the lights go out, most households think first about the fridge, the lift, the phone. Hot water usually comes later — and then, often, as a surprise. A gas water heater sounds like it should be immune to a blackout. After all, it burns gas, not electricity. In practice, the opposite is true for most modern units, and it helps to know why before you decide what to buy.
This is not a brand issue; it is how modern gas heaters are built. A burner does not light itself. On most units sold in the last fifteen to twenty years, an electronic control board has to run a pre-purge fan, read a flow sensor, open the gas valve and fire an igniter before combustion can begin. Every one of those steps is electrical. The published spec sheets for leading tankless brands put the running load roughly in the 60–200 watt range — modest next to an electric heater, but entirely dependent on a live supply. When the grid drops, the safety logic shuts the unit down rather than guessing, so the burner never starts and the tap runs cold.
Storage tanks have one advantage here: a tank that was hot when the power failed stays warm for a while — installers often quote a few hours, depending on insulation and incoming water temperature. A continuous-flow (tankless) heater has no such buffer. No power means no hot water, immediately. That is the single biggest change households make when they move from a tank to a tankless unit, and it is worth understanding before the switch, not during the outage.

A built-in lithium battery and booster pump keep the shower running when the mains supply drops.
There is no single right answer. Each route below solves a real problem and has a real limit; the question is which one matches the way you live.
| Route | What it does well | The honest limit |
|---|---|---|
| Old standing-pilot models | A small flame burns continuously and opens the valve mechanically, so they keep working through an outage | Being phased out in most markets; the pilot consumes gas year-round, and efficiency is lower |
| External backup — UPS, generator or add-on battery kit | Can power the whole unit and, with a generator, other appliances too | Bought and installed separately; output and runtime must be matched to the exact model; portable generators must stay outdoors because of carbon monoxide; field reports put many add-on kits at roughly 20–40 minutes of useful hot water |
| Built-in lithium battery, automatic transfer | The battery is part of the appliance, takes over on its own, and is sized for the heater's own loads | Runtime is finite and depends on how long and how hot you shower; the battery must be charged before the outage |
The first route is a reasonable choice where gas is cheap and outages are brief, and it needs no planning at all — but you are buying an older technology. The second is the most flexible, and for a household that needs the whole home running it is still the right answer; it just asks more of the buyer: sizing, installation, maintenance, safe generator placement. The third is the most compact answer to a narrower question — "how do I keep hot water normal without adding a second system?" — and that is the one this heater is built around.
Power reliability is not uniform, and that is why this feature matters more in some markets than others. Grid operators publish the number: Dubai reported about 0.82 minutes of customer interruption per customer in 2025, and Singapore's figure for 2021–2025 was effectively zero. Leading European utilities are often around fifteen minutes a year. In Indonesia, the average duration improved to about 0.77 hours in 2025, but the number of interruptions rose to roughly 7.45 per year. Add planned safety shutoffs in fire-prone regions and storm-related failures, and it is clear that "a short outage" means very different things in different places. In a market where the grid almost never fails, built-in battery backup is reassurance; where it fails several times a year, it becomes part of the daily routine.
It is worth being precise. In this heater, hot water still comes from gas combustion. The internal 5.2Ah lithium battery does not heat the water and does not turn the unit into an electric heater. What it powers is the set of low-voltage parts that a blackout would otherwise stop: the control board, the fan, the igniter, the gas valve and the booster pump. When mains power drops, the unit transfers to the battery automatically, so combustion continues and the selected temperature holds. On a full charge that means roughly two to three hours of operation, or in the region of fifteen showers.
That claim deserves a reality check. Fifteen showers at eight to twelve minutes each works out to about two to three hours, so the two figures agree — but only under that assumption. Ask any supplier how the number was measured, and treat a runtime quoted without conditions as a claim rather than a fact.

Constant-temperature bathing continues through a power outage, with the panel still lit.
And one point cannot be overstated: "no mains power" is not "no electricity" and not "no gas." The battery must be charged in advance and the gas supply must be connected. Only with both in place can the unit ignite and deliver hot water. It removes the dependence on the wall outlet; it does not remove the need to prepare.
1. Does it transfer automatically, or do I have to switch it over? A manual step is easy to miss at night.
2. What exactly stays powered? "Has a battery" can mean anything from a clock display to the burner system. Confirm the fan, igniter and gas valve.
3. How was the runtime measured? Ask for shower length and temperature setting.
4. Is it built in or added on? An integrated battery is specified with the heater; an add-on kit has to be matched to it.
5. How is it installed? This is an indoor unit, but combustion air and exhaust must be routed outdoors through a correctly fitted flue. No gas heater belongs in a sealed room, and the water is for washing, not drinking.
The first is treating "battery-backed" as "no electricity or no gas" — it means independence from the outlet during an outage, nothing more. The second is letting the battery sit flat for months and finding out on the night it is needed. The third is borrowing a runtime figure from a different setup: an add-on kit, a storage tank, and a built-in battery are not measured the same way, and comparing them as if they were helps nobody.
On certification, ask for the current status rather than a general claim. This unit is designed to international gas-safety standards and CE certification is in active preparation, with approval expected soon.
The useful way to sum this up is not "ours is the strongest." It is: for a household that wants ordinary hot water to survive an ordinary blackout without buying, sizing and maintaining a second system, an integrated battery that takes over by itself is a straightforward answer. For buyers and OEM/ODM partners, that is a claim a customer can check.